S-10 Forum banner

Discussions Showcase Albums Media Media Comments Tags

1-20 of 44 Results
  1. 4wd IFS
    I have a 2003 chevy s10 zr2 with the rough country lift kit on it. It has rough country upper control arms but I can't seem to find what bushings these use. Has anyone ever replaced theirs if so what bushings did you use? I prefer Moog but I'm not picky.
  2. S10 / Sonoma
    So I have a 95 sonoma 4.3, the motor is bout ready to give out, I would put a v8 in there but itll be goin to my kid sister soon anyways, she don't need that kinda power, not at the age of 14, so could I just swap in a motor from a 2002 sonoma? I know I could if I took time anything is possible...
  3. S10 / Sonoma
    Hey so 95 sonoma, 4.3l v6, and supercharger kits for them? I looked around but I cant find them maybe I'm looking in all the wrong spots.
  4. S10 / Sonoma
    Hey, I got me a 95 sonoma 4.3L V6, it is the carbed version, that little air tube that comes down from the round intake, do I need it?
  5. 2.2L - 2nd gen 4-banging
    Greetings, have posted on the past about my 1998 Sonoma throwing and melting plugs, and the last time I replaced the plug it ran great for about 10 minutes at idle, the sure enough after driving, it started running rough again. Finally decided enough of enough and ordered a built head. Got it...
  6. S10 / Sonoma
    So I just got me a 1995 GMC Sonoma 4.3L V6, I wanna get some headers for it and I tried going to summit racing but they said no headers will fit it, I'm brand new to the car/truck scene, (sorry if this is a dumb question but) where would I get some that fit?
  7. S10 / Sonoma
    I’m trying to find info on whether or not a utility shell off a Colorado would fit depth wise in a 94 s10. The shell has two rear barn doors to replace the tailgate and no floor. The bed dimensions are correct but just not sure about the depth with the doors. I appreciate any input, I’ve tried...
  8. Syclone / Typhoon / Sonoma GT
    Was driving through our little town and saw an interesting first Gen Sonoma at the local repair shop. It was a Sonoma SST... I've never heard of an SST, I didn't get a pic of it as I was driving. I'm hoping I'll see it again so I can post a pic. It had full body molding and arches, roll pan and...
  9. S10 / S15
    I have an 86 s15 that I've been working on. The headliner was removed and so was the dome light. The previous owner caused a short in the wire for the dome light so bad it melted the wire. The fuse panel where the HORN/DM fuse is also had gotten too hot. As well as the TAIL/CTSY circuit. They...
  10. S10 / Sonoma
    My Sonoma I recently bought has tint on the third brake light, the headlights were tinted with some spray on stuff and that was pretty easy to remove but I can’t seem to remove the tint on the third brake light. I don’t think it’s film, and I tried to wet sand it with steel wool and some water...
  11. 262ci Forum (4.3)
    I have a 2003 GMC Sonoma 4.3l Vortex. Does anyone know if the pistons that come with it are pressed fit or floating? And if they are press fit is it possible to use the same connecting rod on a full floating piston pin?? Thank you.
  12. S10 / Sonoma
    Hi, I have a 98 S10 what interior parts will bolt in from a 95 Sonoma all, some or none? Thanks.....
  13. S10 / Sonoma
    Hello all, My leafs in the back of my sonoma are sagging and squeaking bad. Haven't gotten around to looking at the bushings and all yet but I'm assuming they're bad. I looked around and found on this forum a similar thread where people talked about using Silverado /other 1/2 ton leaf packs on...
  14. S10 / Sonoma
    Hey everyone I need help and have searched the forums but cant find any direct answers for my situation. Ok so first off I'm building a off road tracked vehicle and I've bought a 2002 sonoma with the 4.3 for my engine. So it will crank over start for 2 seconds and shut off (passkey yes I know)...
  15. Exhaust
    While in the process of replacing a broken exhaust manifold, we encountered this pipe that we cannot identify but think we are going to have to replace too, as it seems the old manifold's bolts are too rusted. It is connected to the manifold tubes and runs farther back into the truck. Anyone...
  16. Transmission & Rearend
    So I recently got a 1998 Sonoma SLS, 2.2l with the 5-speed with 250k miles. I really like this truck. Rides smooth, runs and drives like it's got 1/4 of that milage (Was a gift from my uncle who has owned it since he bought it off the lot in 97 and he's not able to drive a stick anymore due to...
  17. 262ci Forum (4.3)
    I just got a 97’ Sonoma 4.3 auto 4x4 flatbed. It was originally owned by Disney in Orlando. My friend bought it from them and has barely used it over the years. It has just under 9,000 miles on it. Yes, 9,000. I just got the truck today and when I turn the key in the on position, I can’t hear...
  18. S10 / Sonoma
    My 2000 Sonoma zr2 with a 4.3 has a blown head and I already have another engine lined up for it. I have been told that I will have to drop the front diff and I was wondering if there is a way around this? and just all together what is the best way to pull it.
  19. Electrical / Lighting
    Hey everyone, I just joined this forum and am in need of some ideas. A few months back I managed to get my hands on a "barn find" 1997 GMC Sonoma SLT stepside that somebody has installed a smallblock chev 400ci v8 into with an aftermarket 3 speed transmission (its a 'transco' if anybody has...
  20. 2.2L - 2nd gen 4-banging
    Hi guys I'm always reading other people's post for info on my 2.2l s10. Anyway so I have a 2001 gmc Sonoma 2.2l. I did the timing chain because it broke, since I was already into it, I did the gears, and oil pan gasket, and the thrust plate on the cam as well as replacing the cam cover on the...
1-20 of 44 Results
Top