Search Results for ‘nv3500’

I have a 5 speed 4x4 transmission that someone swapped into a 95 blazer 4.3L I purchased from auction. Transmission started making allot of noise and I pulled it out. I am having trouble identifying the specific transmission this is and parts to fix it. And also how to rebuild it. I will attach...

I’m doing a v8 swap on my 99 truck and found a 98 4wd nv3500 trans. It’s the only 98+ nv3500 I’ve been able to find and I was wondering if there would be any way to use this in my swap. I can get a custom made drive shaft but I just need to know if I can somehow use this trans. Thanks!

I’m doing a v8 swap on my 99 truck and found a 98 4wd nv3500 trans. It’s the only 98+ nv3500 I’ve been able to find and I was wondering if there would be any way to use this in my swap. I can get a custom made drive shaft but I just need to know if I can somehow use this trans

I’m gathering parts to swap a 350 into my 99 s10. I found an 89 nv3500 trans out of a full-size truck for sale not too far from me and It’s been rebuilt, comes with clutch and flywheel, and driveshaft yoke. Only issue is that it has an external slave and I’ve heard people say that won’t work in...

Hey guys, so I’ve got a 2000 S10 4x4. It’s got the 4.3 and I believe the nv3500 behind it. I’ve been searching for a replacement shifter for months now and haven’t been able to find anything. I’m not sure if I’m just looking in the wrong places or don’t know enough but here goes. My problem is...

I have a 98 s10 single cab with a 2.2 5spd. Clean truck and going to swap a 5.3 with a nv3500 and Ford 8.8 I have general information what I’ll need to do. I know the big things want but curious on the small stuff. Like the drive shaft, custom? And then steering shaft, heard about the Jeep one...

I have a 92 s10 with a 4.3 Auto and it’s 4x4. The trans is going out. I just picked up a low mileage NV3500 with a NP241C transfer case for dirt cheap. The manual trans and tcase is from a 93 K1500. I know the trans will bolt to the 4.3, but will the transfer case work with my manual 4x4 lever...

I'm putting a '78/'79 SBC in my '91 S10 (currently a 2.8/T5) with a NV3500 out of an S-truck, not sure the year, and a Chevy 12-bolt from Moser engineering and just had a few questions. If anyone knows any of these or has any specific experience it'd be greatly appreciated. What flywheel and...

I recently picked up an 02 S10 that I'm planning on doing an LS swap in. I'm hoping to save as much as possible in the short term and I was wondering if anyone has done a swap and kept the stock NV3500 trans and if so what motor mounts work best for it? I am planning on putting a T-56 in at a...

I have a 1991 S10 (4.3L with 700r4), and I was wanting to throw an NV3500 in there. I know I need everything from a shift knob to the pedal assembly. I know I'll have to cut a hole for the shifter, but as far as installation I don't have a clue. Would I have to get a new crossmember? Would I...

Putting a 350 in my '91 and found a NV3500 from a C1500 on ebay, just wondering if it would fit with no crazy modifications. Don't know much about transmissions, are all GM 3500's the same dimensions?

Hey guys! I was on here not too long ago talking about my manual swap plan. I finally found a really good truck that would allow me to take everything from it and swap it onto mine. Driveshaft length, ecu, transmission, everything. I know the bellhousing from the 2.2 won’t match up to my 4.3...

Hey guys! I have a super clean 60k mile 97 s10 4x4 extended cab with the 4l60e auto transmission. It recently went out on me so I’m deciding to swap in a nv3500 manual rwd transmission! Is there anything I should know before hand? Also how do the driveshaft lengths compare? I know that I need to...

hi, I have an NV3500 with the internal slave cylinder. i would like to install it on my s10 1994 . extended cab. I was wondering which slip yoke I should put on my driveshaft because the current one is too small

I have a 2000 gmc sonoma that i just got finsihed swapping to a nv3500 4x4 So on april 10 everything on the swap is finished but couple things i need help on 1. What should i do with tranny lines 2. I lost half of power steering 3. What should i do on engine light not detecteing auto