S-10 Forum banner

Search results

1-20 of 118 Results
Advanced Search
  1. Slave Cylinder Rod

    Transmission & Rearend
    So I did a 4.3 swap on my '92 with a '92 motor and a '95 trans. All the part numbers match, everything fits, Delco Clutch kit, new flywheel, all is good. I bled the clutch hydraulics on the bench and got a firm master cylinder with the slave blocked. Again, all is good. So, I installed the...
  2. 4.3 5-speed inspcection cover

    Wanted, to Buy
    Surprised i'm having a hard time finding this, but I need a flywheel cover for a '92 4.3 with a 5-speed.
  3. Fog light harness

    S10 / S15
    Much appreciated. Love how all of option harness are separate with dimpled location markers. I'm a big fan of looking factory. Interestingly enough, by '92 the cruise hole is pre-drilled with a plug installed. Guess there were more trucks with than without at that point.
  4. Fog light harness

    S10 / S15
    Here's the two dimples on the firewall.
  5. Fog light harness

    S10 / S15
    Sorry if I wasn't clear there. Actually looking for the hole on the firewall. Let me go snap a pic of the two dimples.
  6. Fog light harness

    S10 / S15
    Can anyone with factory fog lights take a look at what hole the harness passes through? I know the general area, but I see two dimples for uncut factory holes, one high and one low. Just wondering which had the fogs. Got the engine out, so now's the time to do it up correctly. Kinda curious...
  7. Is there a best and worst year of S10 first gen?

    S10 / S15
    Last year for cable speedo was '88. They were changed to vss in late '88, but its a good bet to assume '88's are cable and '89's are electronic. VSS in the cable driven trucks was created via the optical wheel in the cluster as stated above. The photo above looks aftermarket.
  8. fuel pump died; alcohol?

    S10 / S15
    Someone used regular fuel line in the tank and it failed. You MUST use submersible J30R10 line in the tank. It's pricey, but you only need a few inches anyhow. Also for your regular rubber, you gotta use J30R9 fuel injection hose. Anything else will fail ya.
  9. Had a rough weekend

    S10 / S15
    Wrecked my '92. Some kids were in the road, both me and the lady in front of me saw them, but she had better brakes. Fortunately, the tired 2.8 could barely get out of its own way, so I wasn't hauling balls. Being the indestructible bastard it is, the only damage to the motor was the water pump...
  10. frame motor mount ?

    Blazer / Jimmy / Bravada
    What year did you look for? I went for both 1st and 2nd gen years and all there are are the side that bolt to the motor. at around 4 bucks a piece.
  11. frame motor mount ?

    Blazer / Jimmy / Bravada
    Not the frame side. I'm having trouble finding the same thing myself. Might just get the JTR kit, but its such a waste for me.
  12. WTB: 92-ish 4.3 engine harness

    Wanted, to Buy
    Ugh, I was supposed to get my complete 4.3 back from the guy I sold one of my trucks to as part of the deal for selling it cheap. But, the knucklehead decided that cutting the harness was easier for him instead of removing it correctly like I very specifically asked him to. So, I need an engine...
  13. New site look and software upgrade Feedback Thread

    Community Help
    I don't mind the look, but I wish there was a way to make it a little smaller. Everything seems huge now.
  14. WTB: 1st gen power window/lock cross car harness

    Wanted, to Buy
    Ha. Turns out I already had one on the shelf from a 4 door blazer that I can make work. Pretty bad when you don't even know what you have. Anyone have a 2 door drivers side door harness? I'd rather one of those than having to hack up this 4 door harness to change the window switch.
  15. Possible aftermarket Cruise Control module????

    Electrical / Lighting
    I don't know your system, but I also don't see it being an issue to pull. A cruise system is going to need a VSS signal, brake switch input, controls, and some kind of mechanism to hold the throttle. The 4th pic there likely shows your control input with the fine wires, and the brake switch...
  16. Static sound behind dash

    Blazer / Jimmy / Bravada
    I couldn't imagine it being anything but vacuum for that hissing. I would just pull the dash when you're doing that heater core. It sucks, but with all of your trouble, and your heater core, its the right way to do it. These trucks were built with the dash already assembled, so working on them...
  17. WTB: 1st gen power window/lock cross car harness

    Wanted, to Buy
    Actually, power mirror too. I don't know if these are all built into one harness, but I do know they're separate from the dash harness. I've acquired all of the goodies through the years, but never thought to grab this part.
  18. Stereo hardware question (help me figure out what this is)

    S10 / S15
    I'd install this in mine. I like weird factory stuff. Shoot me a PM when you want to ditch it.
  19. WTB: 1st gen 2WD truck dash harness

    Wanted, to Buy
    Doing a dash swap and have a 4WD blazer dash, apparently these are wired differently than the trucks and I want to do my swap in a day/make some changes to the wiring. This is a 92 RCSB, so prolly anything 89 and up would work.
  20. 2.8 timing way off/failed emissions

    60v6 Forum (2.8/3.4)
    Thermostat is a 195, brand new. Here's a snapshot after warming up to operating temp.
1-20 of 118 Results
Top