S-10 Forum banner

Recent content by Sonomanclature

  1. User password reset

    S10 Forum Team to AG Support
    User name: FrEaK_aCcIdEnT Armando has contacted me through facebook about trying to access his account, his old email service was dropped a while ago so he cannot reset his password. His new email address is below. [email protected] his old email for verification ...
  2. Yet another password issue.

    S10 Forum Team to AG Support
    warriorcustoms has tried to reset his password a couple times now but is having issue getting an email. If some one could try sending one out to him. Current Email is [email protected]
  3. SAS for bad roads

    4wd SFA
    In, because wooden templates. Not seen that before.
  4. Prep for the Ascent 44HP/60FF

    4wd SFA
    Well now. So ends this chapter, after combating overheating issues, oil pressure issues, and just a general lack of decent road manners, it is time to stick it int he corner for a little while. I don't plan on putting a SBC back in it at this time, have been looking at a V2203 Kubota diesel...
  5. Project: In The Red ( not an S-series)

    Member Projects
    Been slowly working on this when time is available. Did the drivers floor patches, inner rocker, and part of the kick panel. Tried to pull this out, and ended up giving up after a few hours and just cut it out. Ended up picking up a 67 hood, just been going through and filling in all the...
  6. What did you do to your S10/Sonoma/Hombre Today?. V3

    S10 / Sonoma
    Yea I know, photobucket has gone to shit.
  7. Hi guess if anybody can chime in

    4wd SFA
    Jesus this thread is a waste of Bandwidth. Manual T-case 231, Who cares when it ended, as you will most likely never see an S-series after 97 with a manual T-case unless it has been swapped in. End subject. G80 GOV-Bombs have clutches Period, End subject Honestly OP it just seems you have...
  8. What did you do to your S10/Sonoma/Hombre Today?. V3

    S10 / Sonoma
    Took it out this weekend to do some testing with the new trailer.
  9. Prep for the Ascent 44HP/60FF

    4wd SFA
    Took it out for some testing, ran into a couple issues, Issue 1, passenger hub didn't lock in, which resulted in me loosing traction going op a hill stalling then abruptly rolling 50ft backwards down said hill and jackknifing in the middle. Sketchy as hell. good news, Double low is ****ing...
  10. Prep for the Ascent 44HP/60FF

    4wd SFA
    Pulled the fans off and cut up the unit they were apart of, used an industrial baking sheet to make a shroud and recessed the blades about halfway into that. didn't get pics. Hopefully this helps my cooling issue. Yesterday me and the wife went and finally picked up the camper, it has been...
  11. Project: In The Red ( not an S-series)

    Member Projects
    Another photo dump.
  12. Project: In The Red ( not an S-series)

    Member Projects
    Some more work today. Just a pic dump
  13. Project: In The Red ( not an S-series)

    Member Projects
    So far, got the rolling stock so I can work out fitment issues and sheemetal work.
  14. Prep for the Ascent 44HP/60FF

    4wd SFA
    I never heard it, cant hear a thing over hte exhaust and fans lol. Its still loosing pressure so I have a feeling it is going to be a bearing issue.
  15. Prep for the Ascent 44HP/60FF

    4wd SFA
    Been daily driving it while my mother-in-law has the subaru. Oil pump starting failing when hot would drop 20PSI at 3k rpm, changed it out friday seems to be doing better now. Need to make a rear drive shaft before Moab in hope that it will still be going with me. Also adjusted the rockers...
Top