Syborg Twin Turbo

marlborosyclone · 02-28-2007, 12:03 AM

Good Morning All,

I would like to re-introduce myself my name is Marty. I have been working on this project for the last couple years. This truck was supposed to be a daily driver. I purchased a Sonoma GT so I could build it to drive instead of the Marlboro. However with all projects they sometime start with good intentions and then end up on a completely different path. Since begining this project I have sold the Marlboro to help fund this beast.

Currently the truck is almost ready for paint and will be heading over to Rad Rides by Troy for final paint and bodywork.. The chassis has been set at 4.75 in the rear and 4.25 in the front at it's lowest point for driving. . Front Suspension is by Air Ride and the rear suspension was hand fabricated by Dave at Competition Fabrication ( CompFab Home ) .

The first rendering was done by Bob Thrash at Rad Rides by Troy and the second rendering was done by Carter Hickman.

Build Highlights
* Chevy V6 Bowtie Block 4 Bolt Nodular Caps
* Crower Billet Crankshaft,Oliver Rods w/ JE Pistons
* Pontiac Racing Heads w/ Jesel Valve Train
* Hogan Intake Manifold w/ Wilson Throttle Body
* Precision Turbo's w/ Innovative Waste Gates
* 321 Stainless TT Headers w/Stainless Works Exhaust
* Billet Specialties Serpentine Pulley System
* 4L80E Transmission
* Aeromotive Fuel System
* Big Stuff 3 Ignition w/ MSD Ignition

* Currie Aluminum 9" w/ Aluminum Third Member
* Parralel 4 Bar w/ Air Ride Shock Wave Shocks
* Bell Tech 2" Drop Spindle's & Bell Tech Sway Bar
* Air Ride Upper & Lower Control Arm w/Shock Waves
* Air Ride Suspension "Pro-Ride" System
* 14" Wilwood Brakes Front and Rear
* Dual Master Cylnder with remote Bias in cab Control
* Billet Specialties "SLG 20" Soft Lip Wheels,
* BFG KDW II Tires - 295 45 20 rear & 235 40 18 front

* Fiberglass Front Bumper (modified to allow for air intake for the turbochargers)
* Factory Ground Effect remade in Fiberglass
* Core Support Modified to accept Custom Radiator, Intercooler and A/C Condensor
* Billet Hood Hinges
* Harwood Cowl Induction Hood
* Smoothed Firewall and Hand fabricated Inner Fenders
* "A" Pillar modified to match Fender Lines
* Bed Sides Narrowed to match cab width
* Shaved Door handles, tailgate handle and gas door

* 8 Point Roll Cage
* Sheet Metal Dash Conversion
* Recovered Factory Interior in Viper Leather and Suede
* Carbon Fiber Dash Surround, Center Consule Cover and Shifter Knob
* Autometer Gauges
* American Auto Wire Harness

Fabrication by Comp Fab

There are so many other mods that I can't even list them all.

here are a few pics.

Carter Hickman Design digitalpaint@hokdigitalpaintbooth.com

marlborosyclone · 02-28-2007, 12:04 AM

I have been a lurker for sometime now and i figured it was time to come forward and post some update here.

6linkslam · 02-28-2007, 12:08 AM

nice!! i saw the truck in sport truck magazine.

2kdime · 02-28-2007, 12:13 AM

geyod damn. thats beautiful!!

Twisted Minis · 02-28-2007, 12:19 AM

Thats fvcking cool man.

**travy** · 02-28-2007, 12:24 AM

I saw some of your stuff awhile ago.

I don't have words to say how awesome I think that truck is.

eric s · 02-28-2007, 12:25 AM

simpledime85 · 02-28-2007, 12:30 AM

spechless

**travy** · 02-28-2007, 12:37 AM

by the way "Syborg" is an amazing badass name too

99blkx · 02-28-2007, 01:07 AM

been following this build on SSF for a long ass time.

this truck is above and beyond anything i'ver seen. i don't even wanna know the amount of time and money that will be invested when all is said and done. i just hope to see it in person.

honestly, best truck evar. when done, i think marty could take the riddler if thats allowed....

purevil115 · 02-28-2007, 12:27 PM

holy shit I am in love right now I want that thing keep us posted on it man thats great

PEKO · 02-28-2007, 12:32 PM

I havent seen that in a while. Last time I cant remember when but was in a truck magazine. very nice and very clean.

cpolaris502 · 02-28-2007, 01:46 PM

that thing is amazing, the engine looks so nice! nice work!

jman · 02-28-2007, 03:21 PM

Quote: Originally Posted by 99blkx

been following this build on SSF for a long ass time.

this truck is above and beyond anything i'ver seen. i don't even wanna know the amount of time and money that will be invested when all is said and done. i just hope to see it in person.

honestly, best truck evar. when done, i think marty could take the riddler if thats allowed....

same here.

i just saw this mod, what does it mean

* "A" Pillar modified to match Fender Lines

awesome build.

BIGGERISBETTER · 02-28-2007, 04:01 PM

Ah.. i remember this one.. Awesome too see it's getting closer to being done. Your a maniac

NotaDime · 02-28-2007, 04:12 PM

HOTTNESS!! DAMN, youve got a marlboro to?????

please get up some pics of it too, or a link.

Paul42 · 02-28-2007, 05:01 PM

How wide are your rear wheels and what are the offset? Is your rear end narrowed?

***sdime98*** · 02-28-2007, 05:06 PM

thats so sick, i love it...keep us updated.

clr8210 · 02-28-2007, 05:16 PM

Looks Amazing. Is the fiberglass front bumper a custom made piece or can it be bought somewhere?

NotaDime · 02-28-2007, 05:18 PM

its a sonoma GT bumper i believe.

kevdog · 02-28-2007, 05:20 PM

This truck is gonna be freakin' sweet!

*subscribes*

Prime. · 02-28-2007, 05:36 PM

So nice. Saw it in Sport Truck. It's gonna be awesome.

Lowsonoma03 · 02-28-2007, 08:18 PM

i saw this over at syty.net i believe....nice work man!! looks amazing already!

DarkGreen03 · 02-28-2007, 11:45 PM

I've been following this thing for a long time on s-series forum, its definitly a top notch build, I wanna see this thing finished!

91sonomast · 03-01-2007, 12:21 AM

MARTY!!! So nice of you to join us over here at s10forum lol!! So i will be able to see updates here and at pro-touring.com? Sweet!

By the way: when are more progress pics gonna be up? Im dying to see what kinda craziness is going on in ur garage!

91sonomast · 03-01-2007, 12:21 AM

Quote: Originally Posted by NotaDime

its a sonoma GT bumper i believe.

it was..........and still kinda is a sonoma gt lol

NotaDime · 03-01-2007, 12:26 AM

thought so!

S-10Driver · 03-01-2007, 01:14 AM

i can't wait to see this bad boy finished. i've been following the buildup for a while now.

JediSpam · 03-01-2007, 03:09 AM

wow ridiculous

PEKO · 03-01-2007, 09:46 AM

I really like those wheels. They look very similar to the ones on the NAPA S10 that Overhaulin did. Very nice. On the 1st drawing i mean

BadS15v8 · 03-01-2007, 02:53 PM

What's the predicted power range? Other words what are you planning the motor will produce?

Awesome truck man, good work and good luck.

marlborosyclone · 03-01-2007, 06:14 PM

Quote: Originally Posted by clr8210

Looks Amazing. Is the fiberglass front bumper a custom made piece or can it be bought somewhere?

Yep - you can buy it. ( need complete front cover & support)
Pauls Select -- paulselect@mvdsl.com

You will also need the bumperettes from Scott

sy113@syclone-typhoon.com
GMC Syclone Typhoon Sonoma GT Parts & Accessories

they shoot me an e-mail and i will help you find the frame brackets

marlborosyclone · 03-01-2007, 06:34 PM

Quote: Originally Posted by BadS15v8

What's the predicted power range? Other words what are you planning the motor will produce?

Awesome truck man, good work and good luck.

800hp on pump gas is the goal. However we are going to street tune it for 600hp since I plan to drive it on the Power Tour

My goal is to have it finished by Sema this year

syclonekid43 · 03-01-2007, 06:43 PM

nice. ill have to read more when i get home later

FCKNLOW · 03-01-2007, 07:17 PM

i seen and watched alot of the build on another forum.....i must say.....sickest s-series EVER built....without question.

marlborosyclone · 03-01-2007, 11:26 PM

Good Evening All,

This has been a very long week and a very sad Week.
SyTy/SGT - Forums - Myclone is gone
We lost a great guy in the SyTy Community and he will be Dearly missed.

One of his last post over on syty.net was in my build thread. Dave asked if I would adopt him.
The answer is yes but I think you a little to old to be my son and no you can't drive my truck.
So you are going to have to sit in the passenger seat.

The seat is yours Dave - gonna miss you big guy.

Okay I will try to go to back to the updates.

The New Head Gaskets arrived

Getting ready to rip the truck apart again.

Don't try this at home alone -- not a good idea.
Really I am going to buy a lift for my garage.

Wait I have an idea anyone want to sponsor me.

The Bed off and on it's body work stand.
Looks like I am going to need to contact Caleb and ask him if he set it up for 7 foot tall body men.

Chassis sitting naked.
Actually I started doing a hardware inventory and it's time to get some new nut's and bolts.

Decided to take a few Pics of the chassis while it was apart again.

Just another angle of the rear back half

Tom stopped by on Sunday to help me put the motor back in the truck.
Yep -- missing more bolts time to call Billet Specialties.

Fuel cell located back between the rails.
Yep missing some more bolts.

This has been the hardest post that I have ever done.
Farwell Dave we are all going to miss you.

91sonomast · 03-02-2007, 10:27 AM

wow marty, sorry for ur loss, i read the thread you linked sounds like a great guy. Good luck with the truck this next week, lookin real good!
BTW: isn't it wierd how bolts just up and disappear? Its like socks, you dont know where they go, but they got to go somewhere, and if u could only find them u would be set for life lol!

PEKO · 03-02-2007, 10:38 AM

Yeah really sorry to hear about your buddy. I still love a 1st Gen over a 2nd gen anyday. I have one of each. Just cant wait to see this thing done. Oh and dont worry, im sure youll find the bolts and nuts months after its been completed. I always put them somewhere so they wont get lost and of course i forget where that place is lol

PEKO · 03-02-2007, 10:42 AM

Oh and whats that on the side of the frame rails? Some sort of Cooler?

marlborosyclone · 03-02-2007, 11:35 AM

Quote: Originally Posted by PEKO

Oh and whats that on the side of the frame rails? Some sort of Cooler?

They are both oil coolers. One for the tranny and one for the Engine.

marlborosyclone · 03-02-2007, 11:37 AM

Quote: Originally Posted by 91sonomast

BTW: isn't it wierd how bolts just up and disappear? Its like socks, you dont know where they go, but they got to go somewhere, and if u could only find them u would be set for life lol!

Yep i am okay with the loss of a bolts here or there, it's when you lose your Nut's you have to start being concerned.

marlborosyclone · 03-03-2007, 12:42 AM

Okay

need some help with the interior.

Anything and i mean anyhing you guy's can show me would be great.

jimhrabe · 03-03-2007, 04:43 PM

Geez Marty you sure do get around huh? LOL

marlborosyclone · 03-03-2007, 06:14 PM

Quote: Originally Posted by jimhrabe

Geez Marty you sure do get around huh? LOL

it's easier to get around on a couple BB then it would be with another women. Less chance of me getting in serious trouble with the wife.

greencactus3 · 03-03-2007, 07:08 PM

looks awesome without anything!
whats those things on the side of the framerails?

jman · 03-03-2007, 07:18 PM

Quote:

whats those things on the side of the framerails?

Quote: Originally Posted by marlborosyclone

They are both oil coolers. One for the tranny and one for the Engine.

what he said above

x00 · 03-04-2007, 12:13 AM

welcome to the forum....this is definatelly the coolest project ever.

I have been watching it over at pro-touring ever since page 2 on there..

good luck with it.

0343 · 03-04-2007, 12:42 AM

i just creamed myself.. i want one

Loop · 03-04-2007, 02:28 PM

Quote: Originally Posted by marlborosyclone

Okay

need some help with the interior.

Anything and i mean anyhing you guy's can show me would be great.

What type of help are you needing? Fiberglassing? Seat Covers?

If you need help with fiberglassing NickZigaitis on here is the person to ask.

I do a little sewing on the side so if you have questions about material or anything about seats and seat covers I can answer your questions.

marlborosyclone · 03-04-2007, 02:58 PM

Quote: Originally Posted by Loop

What type of help are you needing? Fiberglassing? Seat Covers?

If you need help with fiberglassing NickZigaitis on here is the person to ask.

I do a little sewing on the side so if you have questions about material or anything about seats and seat covers I can answer your questions.

Actually i am looking for Idea's for the Door Panels.

I want something that looks stock. But it needs some sort of design in the panel in it.

02-28-2007, 12:03 AM	#1
marlborosyclone Registered User Age: 42 Join Date: Oct 2001 Posts: 566 Location: User is: OffLine	Syborg Twin Turbo Good Morning All, I would like to re-introduce myself my name is Marty. I have been working on this project for the last couple years. This truck was supposed to be a daily driver. I purchased a Sonoma GT so I could build it to drive instead of the Marlboro. However with all projects they sometime start with good intentions and then end up on a completely different path. Since begining this project I have sold the Marlboro to help fund this beast. Currently the truck is almost ready for paint and will be heading over to Rad Rides by Troy for final paint and bodywork.. The chassis has been set at 4.75 in the rear and 4.25 in the front at it's lowest point for driving. . Front Suspension is by Air Ride and the rear suspension was hand fabricated by Dave at Competition Fabrication ( CompFab Home ) . The first rendering was done by Bob Thrash at Rad Rides by Troy and the second rendering was done by Carter Hickman. Build Highlights * Chevy V6 Bowtie Block 4 Bolt Nodular Caps * Crower Billet Crankshaft,Oliver Rods w/ JE Pistons * Pontiac Racing Heads w/ Jesel Valve Train * Hogan Intake Manifold w/ Wilson Throttle Body * Precision Turbo's w/ Innovative Waste Gates * 321 Stainless TT Headers w/Stainless Works Exhaust * Billet Specialties Serpentine Pulley System * 4L80E Transmission * Aeromotive Fuel System * Big Stuff 3 Ignition w/ MSD Ignition * Currie Aluminum 9" w/ Aluminum Third Member * Parralel 4 Bar w/ Air Ride Shock Wave Shocks * Bell Tech 2" Drop Spindle's & Bell Tech Sway Bar * Air Ride Upper & Lower Control Arm w/Shock Waves * Air Ride Suspension "Pro-Ride" System * 14" Wilwood Brakes Front and Rear * Dual Master Cylnder with remote Bias in cab Control * Billet Specialties "SLG 20" Soft Lip Wheels, * BFG KDW II Tires - 295 45 20 rear & 235 40 18 front * Fiberglass Front Bumper (modified to allow for air intake for the turbochargers) * Factory Ground Effect remade in Fiberglass * Core Support Modified to accept Custom Radiator, Intercooler and A/C Condensor * Billet Hood Hinges * Harwood Cowl Induction Hood * Smoothed Firewall and Hand fabricated Inner Fenders * "A" Pillar modified to match Fender Lines * Bed Sides Narrowed to match cab width * Shaved Door handles, tailgate handle and gas door * 8 Point Roll Cage * Sheet Metal Dash Conversion * Recovered Factory Interior in Viper Leather and Suede * Carbon Fiber Dash Surround, Center Consule Cover and Shifter Knob * Autometer Gauges * American Auto Wire Harness Fabrication by Comp Fab There are so many other mods that I can't even list them all. here are a few pics. Carter Hickman Design digitalpaint@hokdigitalpaintbooth.com
	[Reply w/Quote]

02-28-2007, 12:04 AM	#2
marlborosyclone Registered User Age: 42 Join Date: Oct 2001 Posts: 566 Location: User is: OffLine	Re: Syborg Twin Turbo I have been a lurker for sometime now and i figured it was time to come forward and post some update here.
	[Reply w/Quote]

02-28-2007, 12:08 AM	#3
6linkslam D.I.L.L.I.G.A.F.? Age: 32 Join Date: Jan 2007 Posts: 585 Location: bossier city,la User is: OffLine	Re: Syborg Twin Turbo nice!! i saw the truck in sport truck magazine.
	[Reply w/Quote]

02-28-2007, 12:13 AM	#4
2kdime Registered User Age: 24 Join Date: Mar 2006 Posts: 1,054 Location: Blue Springs, mo. User is: OffLine	Re: Syborg Twin Turbo geyod damn. thats beautiful!!
	[Reply w/Quote]

02-28-2007, 12:19 AM	#5
Twisted Minis Bob Saget bitch! Age: 21 Join Date: Nov 2005 Posts: 2,415 Location: Windsor, CA User is: OffLine	Re: Syborg Twin Turbo Thats fvcking cool man.
	[Reply w/Quote]

02-28-2007, 12:24 AM	#6
travy Megabyte Age: 23 Join Date: Sep 2006 Posts: 7,938 Location: Vancouver, WA User is: OffLine	Re: Syborg Twin Turbo I saw some of your stuff awhile ago. I don't have words to say how awesome I think that truck is.
	[Reply w/Quote]

02-28-2007, 12:25 AM	#7
eric s (s)AINT Age: 30 Join Date: Feb 2006 Posts: 498 Location: Port Clinton, ohio User is: OffLine	Re: Syborg Twin Turbo
	[Reply w/Quote]

02-28-2007, 12:30 AM	#8
simpledime85 I'll never let go Age: 25 Join Date: Jan 2007 Posts: 177 Location: User is: OffLine	Re: Syborg Twin Turbo spechless
	[Reply w/Quote]

02-28-2007, 12:37 AM	#9
travy Megabyte Age: 23 Join Date: Sep 2006 Posts: 7,938 Location: Vancouver, WA User is: OffLine	Re: Syborg Twin Turbo by the way "Syborg" is an amazing badass name too
	[Reply w/Quote]

02-28-2007, 01:07 AM	#10
99blkx I'm on a boat! Age: 28 Join Date: Mar 2003 Posts: 1,470 Location: hour west of StL User is: OffLine	Re: Syborg Twin Turbo been following this build on SSF for a long ass time. this truck is above and beyond anything i'ver seen. i don't even wanna know the amount of time and money that will be invested when all is said and done. i just hope to see it in person. honestly, best truck evar. when done, i think marty could take the riddler if thats allowed....
	[Reply w/Quote]

02-28-2007, 12:27 PM	#11
purevil115 Registered User Age: 22 Join Date: Feb 2006 Posts: 2,517 Location: lousiville, Ohio User is: OffLine	Re: Syborg Twin Turbo holy shit I am in love right now I want that thing keep us posted on it man thats great
	[Reply w/Quote]

02-28-2007, 12:32 PM	#12
PEKO Strictly Domestic Age: 31 Join Date: Jul 2002 Posts: 2,844 Location: Hudson Co, NJ User is: OffLine	Re: Syborg Twin Turbo I havent seen that in a while. Last time I cant remember when but was in a truck magazine. very nice and very clean.
	[Reply w/Quote]

02-28-2007, 01:46 PM	#13
cpolaris502 The Dreamsicle Age: 21 Join Date: Jul 2005 Posts: 16,425 Location: Rogers, MN User is: Online	Re: Syborg Twin Turbo that thing is amazing, the engine looks so nice! nice work!
	[Reply w/Quote]

02-28-2007, 03:21 PM	#14
jman Hardcore 1st Gen'r Age: 30 Join Date: Jul 2001 Posts: 2,840 Location: Austin, IN User is: OffLine	Re: Syborg Twin Turbo Quote: Originally Posted by 99blkx been following this build on SSF for a long ass time. this truck is above and beyond anything i'ver seen. i don't even wanna know the amount of time and money that will be invested when all is said and done. i just hope to see it in person. honestly, best truck evar. when done, i think marty could take the riddler if thats allowed.... same here. i just saw this mod, what does it mean * "A" Pillar modified to match Fender Lines awesome build. Last edited by jman : 02-28-2007 at 03:24 PM.
	[Reply w/Quote]

02-28-2007, 04:01 PM	#15
BIGGERISBETTER flat blue and layin frame Age: 25 Join Date: Aug 2004 Posts: 5,871 Location: Bolivar, Ohio User is: OffLine	Re: Syborg Twin Turbo Ah.. i remember this one.. Awesome too see it's getting closer to being done. Your a maniac
	[Reply w/Quote]

02-28-2007, 04:12 PM	#16
NotaDime UN-BANNED B!TCHES!!!!! Join Date: Jan 2007 Posts: 5,335 Location: Home. User is: OffLine	Re: Syborg Twin Turbo HOTTNESS!! DAMN, youve got a marlboro to????? please get up some pics of it too, or a link.
	[Reply w/Quote]

02-28-2007, 05:01 PM	#17
Paul42 THE Original Donk! Age: 33 Join Date: Oct 2004 Posts: 776 Location: Vancouver, WA User is: OffLine	Re: Syborg Twin Turbo How wide are your rear wheels and what are the offset? Is your rear end narrowed?
	[Reply w/Quote]

02-28-2007, 05:06 PM	#18
*sdime98* slowly, but surely. Age: 24 Join Date: Feb 2003 Posts: 50,413 Location: Laurel Hill, NC User is: OffLine	Re: Syborg Twin Turbo thats so sick, i love it...keep us updated.
	[Reply w/Quote]

02-28-2007, 05:16 PM	#19
clr8210 Registered User Age: 21 Join Date: Jul 2005 Posts: 323 Location: Greenfield, IN User is: OffLine	Re: Syborg Twin Turbo Looks Amazing. Is the fiberglass front bumper a custom made piece or can it be bought somewhere?
	[Reply w/Quote]

02-28-2007, 05:18 PM	#20
NotaDime UN-BANNED B!TCHES!!!!! Join Date: Jan 2007 Posts: 5,335 Location: Home. User is: OffLine	Re: Syborg Twin Turbo its a sonoma GT bumper i believe.
	[Reply w/Quote]

02-28-2007, 05:20 PM	#21
kevdog bank owned Age: 26 Join Date: Aug 2004 Posts: 2,935 Location: Newark, OH User is: OffLine	Re: Syborg Twin Turbo This truck is gonna be freakin' sweet! subscribes
	[Reply w/Quote]

02-28-2007, 05:36 PM	#22
Prime. Buffa Beats Age: 20 Join Date: Nov 2005 Posts: 1,236 Location: Lawrenceville, GA User is: OffLine	Re: Syborg Twin Turbo So nice. Saw it in Sport Truck. It's gonna be awesome.
	[Reply w/Quote]

02-28-2007, 08:18 PM	#23
Lowsonoma03 Registered Asshole Age: 24 Join Date: Jan 2004 Posts: 7,470 Location: Erie, PA User is: OffLine	Re: Syborg Twin Turbo i saw this over at syty.net i believe....nice work man!! looks amazing already!
	[Reply w/Quote]

02-28-2007, 11:45 PM	#24
DarkGreen03 Baller Status Age: 22 Join Date: Nov 2004 Posts: 554 Location: York, PA User is: OffLine	Re: Syborg Twin Turbo I've been following this thing for a long time on s-series forum, its definitly a top notch build, I wanna see this thing finished!
	[Reply w/Quote]

03-01-2007, 12:21 AM	#25
91sonomast Good Bye SonomaST Age: 25 Join Date: Sep 2005 Posts: 6,134 Location: Murray, KY User is: OffLine	Re: Syborg Twin Turbo MARTY!!! So nice of you to join us over here at s10forum lol!! So i will be able to see updates here and at pro-touring.com? Sweet! By the way: when are more progress pics gonna be up? Im dying to see what kinda craziness is going on in ur garage!
	[Reply w/Quote]

03-01-2007, 12:26 AM	#27
NotaDime UN-BANNED B!TCHES!!!!! Join Date: Jan 2007 Posts: 5,335 Location: Home. User is: OffLine	Re: Syborg Twin Turbo thought so!
	[Reply w/Quote]

03-01-2007, 01:14 AM	#28
S-10Driver Trackside Support Vehicle Age: 25 Join Date: Jan 2004 Posts: 3,856 Location: Warner Robins, GA User is: OffLine	Re: Syborg Twin Turbo i can't wait to see this bad boy finished. i've been following the buildup for a while now.
	[Reply w/Quote]

03-01-2007, 03:09 AM	#29
JediSpam David Age: 23 Join Date: Mar 2005 Posts: 2,666 Location: Texas User is: OffLine	Re: Syborg Twin Turbo wow ridiculous
	[Reply w/Quote]

03-01-2007, 09:46 AM	#30
PEKO Strictly Domestic Age: 31 Join Date: Jul 2002 Posts: 2,844 Location: Hudson Co, NJ User is: OffLine	Re: Syborg Twin Turbo I really like those wheels. They look very similar to the ones on the NAPA S10 that Overhaulin did. Very nice. On the 1st drawing i mean Last edited by PEKO : 03-01-2007 at 09:47 AM.
	[Reply w/Quote]

03-01-2007, 02:53 PM	#31
BadS15v8 Registered User Age: 23 Join Date: Aug 2005 Posts: 1,123 Location: User is: OffLine	Re: Syborg Twin Turbo What's the predicted power range? Other words what are you planning the motor will produce? Awesome truck man, good work and good luck.
	[Reply w/Quote]

03-01-2007, 06:14 PM	#32
marlborosyclone Registered User Age: 42 Join Date: Oct 2001 Posts: 566 Location: User is: OffLine	Re: Syborg Twin Turbo Quote: Originally Posted by clr8210 Looks Amazing. Is the fiberglass front bumper a custom made piece or can it be bought somewhere? Yep - you can buy it. ( need complete front cover & support) Pauls Select -- paulselect@mvdsl.com You will also need the bumperettes from Scott sy113@syclone-typhoon.com GMC Syclone Typhoon Sonoma GT Parts & Accessories they shoot me an e-mail and i will help you find the frame brackets
	[Reply w/Quote]

03-01-2007, 06:34 PM	#33
marlborosyclone Registered User Age: 42 Join Date: Oct 2001 Posts: 566 Location: User is: OffLine	Re: Syborg Twin Turbo Quote: Originally Posted by BadS15v8 What's the predicted power range? Other words what are you planning the motor will produce? Awesome truck man, good work and good luck. 800hp on pump gas is the goal. However we are going to street tune it for 600hp since I plan to drive it on the Power Tour My goal is to have it finished by Sema this year
	[Reply w/Quote]

03-01-2007, 06:43 PM	#34
syclonekid43 import killer Age: 33 Join Date: Sep 2003 Posts: 2,469 Location: User is: OffLine	Re: Syborg Twin Turbo nice. ill have to read more when i get home later
	[Reply w/Quote]

03-01-2007, 07:17 PM	#35
FCKNLOW hates 4cyl s10s Age: 21 Join Date: Mar 2005 Posts: 9,943 Location: Mechanicsburg, Pa User is: OffLine	Re: Syborg Twin Turbo i seen and watched alot of the build on another forum.....i must say.....sickest s-series EVER built....without question.
	[Reply w/Quote]

03-01-2007, 11:26 PM	#36
marlborosyclone Registered User Age: 42 Join Date: Oct 2001 Posts: 566 Location: User is: OffLine	02-27-07 Update - Dedicated to Dave "Myclone" Good Evening All, This has been a very long week and a very sad Week. SyTy/SGT - Forums - Myclone is gone We lost a great guy in the SyTy Community and he will be Dearly missed. One of his last post over on syty.net was in my build thread. Dave asked if I would adopt him. The answer is yes but I think you a little to old to be my son and no you can't drive my truck. So you are going to have to sit in the passenger seat. The seat is yours Dave - gonna miss you big guy. Okay I will try to go to back to the updates. The New Head Gaskets arrived Getting ready to rip the truck apart again. Don't try this at home alone -- not a good idea. Really I am going to buy a lift for my garage. Wait I have an idea anyone want to sponsor me. The Bed off and on it's body work stand. Looks like I am going to need to contact Caleb and ask him if he set it up for 7 foot tall body men. Chassis sitting naked. Actually I started doing a hardware inventory and it's time to get some new nut's and bolts. Decided to take a few Pics of the chassis while it was apart again. Just another angle of the rear back half Tom stopped by on Sunday to help me put the motor back in the truck. Yep -- missing more bolts time to call Billet Specialties. Fuel cell located back between the rails. Yep missing some more bolts. This has been the hardest post that I have ever done. Farwell Dave we are all going to miss you.
	[Reply w/Quote]