Ding Ding Ding Ding... Come And Get It!!!!

***CPWire*** · 06-27-2008, 10:00 AM

Alrighty, We finally have the radiator/condenser/fan package ready to go.
After a few prototypes, and some minor tweaking, here is the result.
A dual core, dual pass, aluminum radiator designed to fit in to the core support of your S truck and work with the LSx engines.
The radiator itself is conservatively rated at around 450hp, and the fans will flow 2780 CFM at 12V.
Both inlet and outlet on the same side of the radiator to match up better with the LSx engines inlets and outlets, as well as give room to route the intake tubing over to the driver's side of the vehicle without any interference.

Radiator - $475.00
Fans/Shroud - $285.00
Condenser - $115.00
Total for complete package - $875.00 + shipping

However... Until July 31st... we will give 10% off of the complete package to any member of s10forum.com. Which brings the total to $787.50 + shipping.

This is for pre-orders, and we should be able to begin shipping around the middle-ish of July.

By the time they are complete and ready to ship, I hope to have part numbers for people to use for rad. hoses. Also, we need to figure out a good spot to put the barb for the steam tube.

Please feel free to ask any questions.

Jonce007 · 06-27-2008, 10:41 AM

Jared, that is a sweet setup!

Do you have the dimensions of the total depth - front of radiator to the back of the fan motors? My current setup is very tight with truck accessories, just wondering if this is comparable or not.

RazorS10 · 06-27-2008, 10:42 AM

Like I said the other day jared thats badass!

ready247 · 06-27-2008, 10:43 AM

how does it mount? any cutting or drilling required? any close up pics of mounting?

looks great btw, ill be getting one, will you have a fan/radiator package available without condensor?

RazorS10 · 06-27-2008, 10:43 AM

Is this a limted amount or this mass production?

**Kampz69** · 06-27-2008, 10:50 AM

looks great! Have you been able to see first hand how it cools?

***CPWire*** · 06-27-2008, 11:00 AM

It's about 6.5" from the back of the radiator, to the farthest point of the fans.

The radiator sits flush against the sheet metal inside the core support.

The only cutting is the center piece of sheet metal in the core support, some trimming for better fit, and drilling 2 holes in the bottom of the support to move the old radiator bottom pieces in.

One other change will be the hood support bracket, it will need to be modified to clear the condenser.

No limited amount, they will be available for as long as they sell.

I have seen first hand how this design/size cools in an S-10, and I know it works great.
I still have some work to do to get this particular vehicle back up and running. Still need to finish the 1-3/4" headers as well.

**Kampz69** · 06-27-2008, 11:09 AM

well, if it cools well down by you, it should cool just about anywhere else. Looks awesome, great job.

RazorS10 · 06-27-2008, 11:12 AM

Trust me they will sell I'm placing an order here soon.

91sonomast · 06-27-2008, 01:03 PM

man jared you are amazing, you guys are doing big things for the LSx s10 guys.

***CPWire*** · 06-27-2008, 03:27 PM

I'm trying.
The biggest problem as we grow, is getting my employees to care about the products going out the door as much as I do.

Constantly trying to improve the QC procedures on the wiring.

**Kampz69** · 06-27-2008, 03:32 PM

that isnt a problem only at your workplace Jared LOL

NateZQ8 · 06-27-2008, 05:20 PM

What about just rad and fans (NO AC here)

NateZQ8 · 06-27-2008, 05:22 PM

[quote=97 SS 350;5367427]

QUOTE]

Are those the new headers your trying out that I see there?

BUCKET · 06-27-2008, 05:26 PM

ummm I HATE U!

lol...nice work

***CPWire*** · 06-27-2008, 05:38 PM

[quote=NateZQ8;5368331]

Quote: Originally Posted by 97 SS 350

QUOTE]

Are those the new headers your trying out that I see there?

MMMMMMMaybe

***CPWire*** · 06-27-2008, 05:56 PM

Quote: Originally Posted by NateZQ8

What about just rad and fans (NO AC here)

Don't know, I was thinking just a discount for people that wanted the whole package.
Maybe 5% off without the Condenser, and 5% off if someone wants just the rad alone.

s10-den · 06-27-2008, 06:41 PM

Jared, any idea if that ac condencer fits in front on a 93??I need a smaller ac condencer bad!!

***CPWire*** · 06-27-2008, 07:16 PM

I would assume so, we have used them on older square body style trucks in the past.

Thizz_Xtreme · 06-27-2008, 08:54 PM

I'm lovin it, cant wait till i can get mine. . .

91sonomast · 06-27-2008, 09:09 PM

Quote: Originally Posted by 97 SS 350

I'm trying.
The biggest problem as we grow, is getting my employees to care about the products going out the door as much as I do.

Constantly trying to improve the QC procedures on the wiring.

every company has that problem. there are some who care and want to make the best thing possible, and some who just want the work day to end.

v8power · 06-27-2008, 11:43 PM

well, theres the dog thats always barking when I call !!!!

***CPWire*** · 06-28-2008, 07:23 AM

Quote: Originally Posted by v8power

well, theres the dog thats always barking when I call !!!!

Actually, that's the quiet one. She is standing there waiting to jump on my Beagle, which is the one you always hear barking.

bitchin sonoma · 06-28-2008, 04:54 PM

only if you had done last year, i already bought a be cool radiator rated at 350 hp.and twin electric fans out of a 1996 impala ss!!

bitchin sonoma · 06-28-2008, 04:57 PM

Quote: Originally Posted by 97 SS 350

I'm trying.
The biggest problem as we grow, is getting my employees to care about the products going out the door as much as I do.

Constantly trying to improve the QC procedures on the wiring.

your right about that, it's like my business we make fresh food, and the workers never put much effort, some do and some don't, i guess people just really work for the money.It's nice to work for the money an actually give love to making the products!!

***SweetS10V8*** · 06-29-2008, 02:29 PM

Who makes the radiator??

RedSpeck_09 · 06-29-2008, 06:08 PM

How wel will that setup function with the corvette style power steering resevoir on the driver's side with respect to routing the air intake?

***CPWire*** · 06-30-2008, 06:56 PM

Quote: Originally Posted by RedSpeck_09

How wel will that setup function with the corvette style power steering resevoir on the driver's side with respect to routing the air intake?

Should fit fine...

RedSpeck_09 · 06-30-2008, 10:26 PM

Good deal man. Now why didn't you have all this stuff when I was bothering you 4 years ago? You've come a long way since leaving Lee. Keep up the good work man.

King_Ice_Flash2 · 07-01-2008, 09:47 AM

Very nice!
I am posting this in the blowers/bottles section.
But I want an additional 10% off for advertising

**Kampz69** · 07-01-2008, 11:31 AM

Quote: Originally Posted by RedSpeck_09

Good deal man. Now why didn't you have all this stuff when I was bothering you 4 years ago? You've come a long way since leaving Lee. Keep up the good work man.

LOL, Lees High Tech Trucks. I forgot about them. They had some sweet trucks on that website.

***CPWire*** · 07-01-2008, 12:07 PM

Wow... that is a past I would like to get away from.
Sweet trucks, all with really pissed off owners by the time they got them back.

He ran that company in to the ground so bad that he changed the name, and moved to another shop hoping no one will be able to find him.

**Kampz69** · 07-01-2008, 12:15 PM

I remember there was a red Xtreme on that site that had some awesome wheels...they were super wide. May have been HRE, but I dont remember....that was a long time ago.

sorry to dig up bad memories Jared lol

***CPWire*** · 07-01-2008, 12:20 PM

**Kampz69** · 07-01-2008, 01:29 PM

yup, those are the wheels exactly, with the massive 315's. i remember emailing way back then asking about the offset, but it was a "secret" lol

***philntx*** · 07-01-2008, 02:12 PM

***CPWire*** · 07-01-2008, 02:14 PM

We are going to be putting 315/35-17's on the truck I have here now...
These:
http://www.zeforged.com/images/gallery/cus/29_bg.gif

**Kampz69** · 07-01-2008, 02:21 PM

those trucks look great. how wide are those Hart wheels anyway?

***philntx*** · 07-01-2008, 02:22 PM

Quote: Originally Posted by 97 SS 350

These:
http://www.zeforged.com/images/gallery/cus/29_bg.gif

Wow! Those are perfect!

**Kampz69** · 07-01-2008, 02:23 PM

Quote: Originally Posted by 97 SS 350

We are going to be putting 315/35-17's on the truck I have here now...
These:
http://www.zeforged.com/images/gallery/cus/29_bg.gif

those look nice too...sorry to hijack this thread guys lol

2000extemeturbo · 07-01-2008, 02:50 PM

Is there any warranty on the radiator?
$475 is a lot to pay, especially if the welds start to fail after 6 or 8 months.

***CPWire*** · 07-01-2008, 03:15 PM

1 year warranty on all parts.

tiresmokinV8 · 07-01-2008, 03:15 PM

No faith in CPW?? LOL Im sure there would be some guarantee against flaws.

2000extemeturbo · 07-01-2008, 03:32 PM

Quote: Originally Posted by tiresmokinV8

No faith in CPW?? LOL Im sure there would be some guarantee against flaws.

Having faith is kind of like making an assumption. We all know what happens when we assume. I'd prefer to ask a simple question and get a simple answer. (thank you CPW)

RazorS10 · 07-02-2008, 07:14 PM

radiator looks like it gives more room up front.

***CPWire*** · 07-02-2008, 07:34 PM

Quote: Originally Posted by RazorS10

radiator looks like it gives more room up front.

Yes it does, that is a big part of what we were going for.

s10-den · 07-03-2008, 03:39 PM

Thats what I was looking at, the room,But, I guess alot didnt move the rad. forward to begin with!?

s10-den · 07-03-2008, 08:42 PM

That black extrem was on abay for sale,but couldnt get any money for it.Chuck used to own that, I talked to him when it was first built and was going to buy it, but couldnt convince the wife it was a good deal..lol

Jonce007 · 07-03-2008, 11:38 PM

Quote: Originally Posted by s10-den

That black extrem was on abay for sale,but couldnt get any money for it.Chuck used to own that, I talked to him when it was first built and was going to buy it, but couldnt convince the wife it was a good deal..lol

I saw that on eBay too - sweet damn truck

cam75w/ls1 · 07-10-2008, 10:09 PM

It's for sale on the Austin,Texas craigslist last I checked.

06-27-2008, 10:00 AM	#1
*CPWire* Makin Sparks Age: 31 Join Date: Jun 2002 Posts: 1,206 Location: Hudson, Florida User is: OffLine	Ding Ding Ding Ding... Come And Get It!!!! Alrighty, We finally have the radiator/condenser/fan package ready to go. After a few prototypes, and some minor tweaking, here is the result. A dual core, dual pass, aluminum radiator designed to fit in to the core support of your S truck and work with the LSx engines. The radiator itself is conservatively rated at around 450hp, and the fans will flow 2780 CFM at 12V. Both inlet and outlet on the same side of the radiator to match up better with the LSx engines inlets and outlets, as well as give room to route the intake tubing over to the driver's side of the vehicle without any interference. Radiator - $475.00 Fans/Shroud - $285.00 Condenser - $115.00 Total for complete package - $875.00 + shipping However... Until July 31st... we will give 10% off of the complete package to any member of s10forum.com. Which brings the total to $787.50 + shipping. This is for pre-orders, and we should be able to begin shipping around the middle-ish of July. By the time they are complete and ready to ship, I hope to have part numbers for people to use for rad. hoses. Also, we need to figure out a good spot to put the barb for the steam tube. Please feel free to ask any questions. Last edited by CPWire : 06-27-2008 at 10:07 AM.
	[Reply w/Quote]

06-27-2008, 10:41 AM	#2
Jonce007 Registered User Age: 32 Join Date: Mar 2008 Posts: 298 Location: User is: OffLine	Re: Ding Ding Ding Ding... Come And Get It!!!! Jared, that is a sweet setup! Do you have the dimensions of the total depth - front of radiator to the back of the fan motors? My current setup is very tight with truck accessories, just wondering if this is comparable or not.
	[Reply w/Quote]

06-27-2008, 10:42 AM	#3
RazorS10 Registered User Join Date: Mar 2007 Posts: 406 Location: User is: OffLine	Re: Ding Ding Ding Ding... Come And Get It!!!! Like I said the other day jared thats badass!
	[Reply w/Quote]

06-27-2008, 10:43 AM	#4
ready247 Registered User Age: 44 Join Date: Apr 2003 Posts: 94 Location: User is: OffLine	Re: Ding Ding Ding Ding... Come And Get It!!!! how does it mount? any cutting or drilling required? any close up pics of mounting? looks great btw, ill be getting one, will you have a fan/radiator package available without condensor?
	[Reply w/Quote]

06-27-2008, 10:43 AM	#5
RazorS10 Registered User Join Date: Mar 2007 Posts: 406 Location: User is: OffLine	Re: Ding Ding Ding Ding... Come And Get It!!!! Is this a limted amount or this mass production?
	[Reply w/Quote]

06-27-2008, 10:50 AM	#6
Kampz69 Need LSx swap..... Age: 31 Join Date: Feb 2002 Posts: 2,071 Location: SW Chicago burbs User is: OffLine	Re: Ding Ding Ding Ding... Come And Get It!!!! looks great! Have you been able to see first hand how it cools?
	[Reply w/Quote]

06-27-2008, 11:00 AM	#7
*CPWire* Makin Sparks Age: 31 Join Date: Jun 2002 Posts: 1,206 Location: Hudson, Florida User is: OffLine	Re: Ding Ding Ding Ding... Come And Get It!!!! It's about 6.5" from the back of the radiator, to the farthest point of the fans. The radiator sits flush against the sheet metal inside the core support. The only cutting is the center piece of sheet metal in the core support, some trimming for better fit, and drilling 2 holes in the bottom of the support to move the old radiator bottom pieces in. One other change will be the hood support bracket, it will need to be modified to clear the condenser. No limited amount, they will be available for as long as they sell. I have seen first hand how this design/size cools in an S-10, and I know it works great. I still have some work to do to get this particular vehicle back up and running. Still need to finish the 1-3/4" headers as well.
	[Reply w/Quote]

06-27-2008, 11:09 AM	#8
Kampz69 Need LSx swap..... Age: 31 Join Date: Feb 2002 Posts: 2,071 Location: SW Chicago burbs User is: OffLine	Re: Ding Ding Ding Ding... Come And Get It!!!! well, if it cools well down by you, it should cool just about anywhere else. Looks awesome, great job.
	[Reply w/Quote]

06-27-2008, 11:12 AM	#9
RazorS10 Registered User Join Date: Mar 2007 Posts: 406 Location: User is: OffLine	Re: Ding Ding Ding Ding... Come And Get It!!!! Trust me they will sell I'm placing an order here soon.
	[Reply w/Quote]

06-27-2008, 01:03 PM	#10
91sonomast Good Bye SonomaST Age: 25 Join Date: Sep 2005 Posts: 6,019 Location: Murray, KY User is: OffLine	Re: Ding Ding Ding Ding... Come And Get It!!!! man jared you are amazing, you guys are doing big things for the LSx s10 guys.
	[Reply w/Quote]

06-27-2008, 03:27 PM	#11
*CPWire* Makin Sparks Age: 31 Join Date: Jun 2002 Posts: 1,206 Location: Hudson, Florida User is: OffLine	Re: Ding Ding Ding Ding... Come And Get It!!!! I'm trying. The biggest problem as we grow, is getting my employees to care about the products going out the door as much as I do. Constantly trying to improve the QC procedures on the wiring.
	[Reply w/Quote]

06-27-2008, 03:32 PM	#12
Kampz69 Need LSx swap..... Age: 31 Join Date: Feb 2002 Posts: 2,071 Location: SW Chicago burbs User is: OffLine	Re: Ding Ding Ding Ding... Come And Get It!!!! that isnt a problem only at your workplace Jared LOL
	[Reply w/Quote]

06-27-2008, 05:20 PM	#13
NateZQ8 WHAAAh? Age: 27 Join Date: Apr 2003 Posts: 1,392 Location: IOWA, land of Corn and Pork User is: OffLine	Re: Ding Ding Ding Ding... Come And Get It!!!! What about just rad and fans (NO AC here)
	[Reply w/Quote]

06-27-2008, 05:22 PM	#14
NateZQ8 WHAAAh? Age: 27 Join Date: Apr 2003 Posts: 1,392 Location: IOWA, land of Corn and Pork User is: OffLine	Re: Ding Ding Ding Ding... Come And Get It!!!! [quote=97 SS 350;5367427] QUOTE] Are those the new headers your trying out that I see there?
	[Reply w/Quote]

06-27-2008, 05:26 PM	#15
BUCKET RITALIN, IT LOVES ME! Age: 29 Join Date: Apr 2005 Posts: 3,703 Location: c-view FL User is: OffLine	Re: Ding Ding Ding Ding... Come And Get It!!!! ummm I HATE U! lol...nice work
	[Reply w/Quote]

06-27-2008, 05:38 PM	#16
*CPWire* Makin Sparks Age: 31 Join Date: Jun 2002 Posts: 1,206 Location: Hudson, Florida User is: OffLine	Re: Ding Ding Ding Ding... Come And Get It!!!! [quote=NateZQ8;5368331] Quote: Originally Posted by 97 SS 350 QUOTE] Are those the new headers your trying out that I see there? MMMMMMMaybe
	[Reply w/Quote]

06-27-2008, 05:56 PM	#17
*CPWire* Makin Sparks Age: 31 Join Date: Jun 2002 Posts: 1,206 Location: Hudson, Florida User is: OffLine	Re: Ding Ding Ding Ding... Come And Get It!!!! Quote: Originally Posted by NateZQ8 What about just rad and fans (NO AC here) Don't know, I was thinking just a discount for people that wanted the whole package. Maybe 5% off without the Condenser, and 5% off if someone wants just the rad alone.
	[Reply w/Quote]

06-27-2008, 06:41 PM	#18
s10-den takes 2 balls in our game Age: 37 Join Date: Nov 2005 Posts: 4,416 Location: florida User is: OffLine	Re: Ding Ding Ding Ding... Come And Get It!!!! Jared, any idea if that ac condencer fits in front on a 93??I need a smaller ac condencer bad!!
	[Reply w/Quote]

06-27-2008, 07:16 PM	#19
*CPWire* Makin Sparks Age: 31 Join Date: Jun 2002 Posts: 1,206 Location: Hudson, Florida User is: OffLine	Re: Ding Ding Ding Ding... Come And Get It!!!! I would assume so, we have used them on older square body style trucks in the past.
	[Reply w/Quote]

06-27-2008, 08:54 PM	#20
Thizz_Xtreme Thizz or Die u bezzy. . . Age: 22 Join Date: Aug 2007 Posts: 95 Location: Fresno, CA AKA The Central Valley User is: OffLine	Re: Ding Ding Ding Ding... Come And Get It!!!! I'm lovin it, cant wait till i can get mine. . .
	[Reply w/Quote]

06-27-2008, 09:09 PM	#21
91sonomast Good Bye SonomaST Age: 25 Join Date: Sep 2005 Posts: 6,019 Location: Murray, KY User is: OffLine	Re: Ding Ding Ding Ding... Come And Get It!!!! Quote: Originally Posted by 97 SS 350 I'm trying. The biggest problem as we grow, is getting my employees to care about the products going out the door as much as I do. Constantly trying to improve the QC procedures on the wiring. every company has that problem. there are some who care and want to make the best thing possible, and some who just want the work day to end.
	[Reply w/Quote]

06-27-2008, 11:43 PM	#22
v8power Toy Fabricator Join Date: Feb 2004 Posts: 573 Location: User is: OffLine	Re: Ding Ding Ding Ding... Come And Get It!!!! well, theres the dog thats always barking when I call !!!! Last edited by v8power : 06-27-2008 at 11:44 PM.
	[Reply w/Quote]

06-28-2008, 07:23 AM	#23
*CPWire* Makin Sparks Age: 31 Join Date: Jun 2002 Posts: 1,206 Location: Hudson, Florida User is: OffLine	Re: Ding Ding Ding Ding... Come And Get It!!!! Quote: Originally Posted by v8power well, theres the dog thats always barking when I call !!!! Actually, that's the quiet one. She is standing there waiting to jump on my Beagle, which is the one you always hear barking.
	[Reply w/Quote]

06-28-2008, 04:54 PM	#24
bitchin sonoma he,he,he project over kil Age: 24 Join Date: Jul 2003 Posts: 1,543 Location: Benton harbor, Michigan User is: OffLine	Re: Ding Ding Ding Ding... Come And Get It!!!! only if you had done last year, i already bought a be cool radiator rated at 350 hp.and twin electric fans out of a 1996 impala ss!!
	[Reply w/Quote]

06-28-2008, 04:57 PM	#25
bitchin sonoma he,he,he project over kil Age: 24 Join Date: Jul 2003 Posts: 1,543 Location: Benton harbor, Michigan User is: OffLine	Re: Ding Ding Ding Ding... Come And Get It!!!! Quote: Originally Posted by 97 SS 350 I'm trying. The biggest problem as we grow, is getting my employees to care about the products going out the door as much as I do. Constantly trying to improve the QC procedures on the wiring. your right about that, it's like my business we make fresh food, and the workers never put much effort, some do and some don't, i guess people just really work for the money.It's nice to work for the money an actually give love to making the products!!
	[Reply w/Quote]

06-29-2008, 06:08 PM	#27
RedSpeck_09 weatherman Age: 25 Join Date: Jan 2002 Posts: 2,194 Location: pensacola/tallahassee User is: OffLine	Re: Ding Ding Ding Ding... Come And Get It!!!! How wel will that setup function with the corvette style power steering resevoir on the driver's side with respect to routing the air intake?
	[Reply w/Quote]

06-30-2008, 06:56 PM	#28
*CPWire* Makin Sparks Age: 31 Join Date: Jun 2002 Posts: 1,206 Location: Hudson, Florida User is: OffLine	Re: Ding Ding Ding Ding... Come And Get It!!!! Quote: Originally Posted by RedSpeck_09 How wel will that setup function with the corvette style power steering resevoir on the driver's side with respect to routing the air intake? Should fit fine...
	[Reply w/Quote]

06-30-2008, 10:26 PM	#29
RedSpeck_09 weatherman Age: 25 Join Date: Jan 2002 Posts: 2,194 Location: pensacola/tallahassee User is: OffLine	Re: Ding Ding Ding Ding... Come And Get It!!!! Good deal man. Now why didn't you have all this stuff when I was bothering you 4 years ago? You've come a long way since leaving Lee. Keep up the good work man.
	[Reply w/Quote]

07-01-2008, 09:47 AM	#30
King_Ice_Flash2 Will work for turbo parts Join Date: Jan 2007 Posts: 2,783 Location: SE, WI User is: OffLine	Re: Ding Ding Ding Ding... Come And Get It!!!! Very nice! I am posting this in the blowers/bottles section. But I want an additional 10% off for advertising
	[Reply w/Quote]

07-01-2008, 11:31 AM	#31
Kampz69 Need LSx swap..... Age: 31 Join Date: Feb 2002 Posts: 2,071 Location: SW Chicago burbs User is: OffLine	Re: Ding Ding Ding Ding... Come And Get It!!!! Quote: Originally Posted by RedSpeck_09 Good deal man. Now why didn't you have all this stuff when I was bothering you 4 years ago? You've come a long way since leaving Lee. Keep up the good work man. LOL, Lees High Tech Trucks. I forgot about them. They had some sweet trucks on that website.
	[Reply w/Quote]

07-01-2008, 12:07 PM	#32
*CPWire* Makin Sparks Age: 31 Join Date: Jun 2002 Posts: 1,206 Location: Hudson, Florida User is: OffLine	Re: Ding Ding Ding Ding... Come And Get It!!!! Wow... that is a past I would like to get away from. Sweet trucks, all with really pissed off owners by the time they got them back. He ran that company in to the ground so bad that he changed the name, and moved to another shop hoping no one will be able to find him. Last edited by CPWire : 07-01-2008 at 12:08 PM.
	[Reply w/Quote]

07-01-2008, 12:15 PM	#33
Kampz69 Need LSx swap..... Age: 31 Join Date: Feb 2002 Posts: 2,071 Location: SW Chicago burbs User is: OffLine	Re: Ding Ding Ding Ding... Come And Get It!!!! I remember there was a red Xtreme on that site that had some awesome wheels...they were super wide. May have been HRE, but I dont remember....that was a long time ago. sorry to dig up bad memories Jared lol
	[Reply w/Quote]

07-01-2008, 01:29 PM	#35
Kampz69 Need LSx swap..... Age: 31 Join Date: Feb 2002 Posts: 2,071 Location: SW Chicago burbs User is: OffLine	Re: Ding Ding Ding Ding... Come And Get It!!!! yup, those are the wheels exactly, with the massive 315's. i remember emailing way back then asking about the offset, but it was a "secret" lol
	[Reply w/Quote]

07-01-2008, 02:12 PM	#36
*philntx* Build them right....Mod Age: 54 Join Date: Jul 2006 Posts: 2,123 Location: Plano TX User is: OffLine	Wheels on the Truck
	[Reply w/Quote]

07-01-2008, 02:14 PM	#37
*CPWire* Makin Sparks Age: 31 Join Date: Jun 2002 Posts: 1,206 Location: Hudson, Florida User is: OffLine	Re: Ding Ding Ding Ding... Come And Get It!!!! We are going to be putting 315/35-17's on the truck I have here now... These: http://www.zeforged.com/images/gallery/cus/29_bg.gif
	[Reply w/Quote]