S10Forum

Sanderson LS1 S10 Swap Headers

FirstGensForever — Thu, 26 May 2011 02:05:02 -0400

by: FirstGensForever

Description: These are brand new, were bolted to the engine in the truck but never had exhaust attached and truck wasn't run with them on, swapped out for a set of the BRP mid length headers. These were purchased from current performance and ceramic coated by them not sanderson. It is a 2000 degree coating and has a few very small scuffs from install but not noticible and it didn't take any of the coating off. These are 1.5 primary and 2.5 collector, these will support 500 hp with a good 3" dual exhaust.

82-97 Hurst Short Throw Shifter, fits T5 5 Speed.

FirstGensForever — Thu, 26 May 2011 01:56:11 -0400

by: FirstGensForever

Description: Ths is a hurst short throw shifter that will fit all s10's from 82-97 that have a T5 5 speed trans. Bought for my 93 and only used for about 5k miles. Will include a hurst super boot that replaces the stock boot perfectly.

82-97 S10 5 speed center console

FirstGensForever — Thu, 26 May 2011 01:47:29 -0400

by: FirstGensForever

Description: This is a graphite 94-97 factory 5 speed center console, will also fit first gen trucks and blazers as I had it in my 93.

93 S10 WC T5 Transmission

FirstGensForever — Thu, 26 May 2011 01:39:02 -0400

by: FirstGensForever

Description: 93 WC spec T5 trans. Has 55k miles came out of my 93 2.8 RCSB. swapping in a 350/T56 don't need this anymore. I bought it used from a salvage yard after my stock t5 broke due to lack of lubrication, was in my truck for about 5k miles ran smooth and quiet. Any questions feel free to ask, if your in dallas, austin, or Houston area im willing to meet to save on shipping.

WTB: 85-89 Astro Van T5 4.3L bellhousing.

FirstGensForever — Wed, 16 Jun 2010 01:55:55 -0400

by: FirstGensForever

Description: The early first Gen astro/safari vans offered a T5 manual trans behind the 4.3 and I'm looking for the bellhousing, clutch fork and slave cylinder. The bell is the most important part. Thanks

96-02 5.7L Vortec Roller Cam Bare Block

FirstGensForever — Mon, 14 Jun 2010 17:05:57 -0400

by: FirstGensForever

Description: This is a STD bore 5.7L bare block. I bought it for a project a few years ago and decided to go with an LS engine instead. It is the newer 96 vortec roller cam block, its rusty but a good used block i bought from a local machine shop that thoroughly checked it out to make sure it was good. The cam is still installed but other than that its just a bare block ready to get cleaned up and machined. Its just taking up space in my garage as i have no use for it. Im asking 50 bucks and would prefer somewhat local, San Antonio, Austin, Dallas or houston and im willing to meet you in the middle somewhere to make the deal, i will ship but all shipping cost will be on the buyer. Any questions feel free to ask.

Kenwood KFC-4675C 4x6 Dash Speakers

FirstGensForever — Mon, 14 Jun 2010 16:58:58 -0400

by: FirstGensForever

Description: These are brand new in the box, great replacement speakers for the dash of every S10, as the factory speakers are horrible. These are 70 bucks from crutchfield, im asking 45 shipped. I dont have any pics but if you want to see them i can take some with my phone and text them to you. Im in Austin Tx so if your local or close by im willing to meet and not have to ship.